CAPE CANAVERAL, Fla. – Inside Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians work inside the aft compartment of the space shuttle Endeavour as replica shuttle main engine RSME number 3 is installed…
KSC-2012-3779
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians move the Hyster forklift into position for installation of replica shuttle main engine RSME number 3 on the space shuttle End…
KSC-2012-3774
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 1 on the space shuttle Endeavour.      The work is…
KSC-2012-3730
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 1 on the space shuttle Endeavour.      The work is…
KSC-2012-3728
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians install replica shuttle main engine RSME number 3 on the space shuttle Endeavour.      The work is part of Transition and Ret…
KSC-2012-3780
CAPE CANAVERAL, Fla. – A close-up view of replica shuttle main engine RSME number 1 recently installed on space shuttle Endeavour in Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida.      The work is part of Trans…
KSC-2012-3745
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 1 on the space shuttle Endeavour. The orbiter is s…
KSC-2012-3727
CAPE CANAVERAL, Fla. – Technicians keep a close watch as the Hyster forklift backs away from the space shuttle Endeavour following installation of replica shuttle main engine RSME number 3 inside Orbiter Processing Facility Bay 2 at NASA’s…
KSC-2012-3782
In Orbiter Processing Facility bay 2, technicians on a Hyster forklift maneuver space shuttle main engine no. 3 into place on Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter…
Space Shuttle Main Engine 3 install in Endeavor
This photo shows the second RS-25 engine attached to the core stage for NASA’s Space Launch System rocket for the agency’s Artemis I mission to the Moon. Engineers and technicians at NASA’s Michoud Assembly Facility in New Orleans structura…
Second RS-25 Engine Attached to NASA Moon Rocket
S88-29076 (10 Jan 1988) --- KSC employees work together to carefully guide a 7,000 pound main engine into the number one position in Discovery's aft compartment.  Because of the engine's weight and size, special handling equipment is needed…
STS-26 Discovery, OV-103, SSME (2019) installed in position number one at KSC
The engine vertical installer for NASA’s Space Launch System (SLS) is inside the Vehicle Assembly at NASA’s Kennedy Space Center in Florida on April 25, 2019. Preparations are underway to lift the engine installer up and into High Bay 3. Th…
Engine Vertical Installer Arrival
The engine vertical installer for NASA’s Space Launch System (SLS) is inside the Vehicle Assembly at NASA’s Kennedy Space Center in Florida on April 25, 2019. The engine installer will be lifted up by crane for transfer to High Bay 3. The e…
Engine Vertical Installer Arrival
The engine vertical installer for NASA’s Space Launch System (SLS) arrives by large transport truck at NASA’s Kennedy Space Center in Florida on April 25, 2019. The engine installer arrived from the manufacturer, Precision Fabrication and C…
Engine Vertical Installer Arrival
CAPE CANAVERAL, Fla. – Technicians keep a close watch as the Hyster forklift arrives at Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida. Replica shuttle main engine RSME number 3 is being delivered for installati…
KSC-2012-3772
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians move the Hyster forklift into position for installation of replica shuttle main engine RSME number 3 on the space shuttle End…
KSC-2012-3775
CAPE CANAVERAL, Fla. - In this wide-angle view inside Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engines 3 RSME has been installed on the space shuttle Endeavour. The orbiter is surroun…
KSC-2012-3785
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engine RSME number 1 has been installed on space shuttle Endeavour. The orbiter is surrounded by work platforms allo…
KSC-2012-3746
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 1 at NASA’s Kennedy Space Center in Florida, technicians work with the Hyster forklift as replica shuttle main engine RSME number 3 is installed on the space shuttle Endeavour.…
KSC-2012-3776
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 3 on the space shuttle Endeavour.      The work is…
KSC-2012-3778
CAPE CANAVERAL, Fla. - In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engine RSME number 1 has been installed on space shuttle Endeavour. The orbiter is surrounded by work platforms allo…
KSC-2012-3743
CAPE CANAVERAL, Fla. – In an overhead view, technicians work inside the aft compartment of the space shuttle Endeavour during installation of replica shuttle main engine RSME number 3 in Orbiter Processing Facility Bay 2 at NASA’s Kennedy S…
KSC-2012-3777
CAPE CANAVERAL, Fla. – At NASA’s Kennedy Space Center in Florida, the Hyster forklift arrives at Orbiter Processing Facility Bay 2 delivering replica shuttle main engine RSME number 3 for installation on space shuttle Endeavour.      The wo…
KSC-2012-3771
CAPE CANAVERAL, Fla. – At NASA’s Kennedy Space Center in Florida, the Hyster forklift arrives at Orbiter Processing Facility Bay 2 delivering replica shuttle main engine RSME number 3 for installation on space shuttle Endeavour.      The wo…
KSC-2012-3770
In Orbiter Processing Facility bay 2, technicians on a Hyster forklift maneuver space shuttle main engine no. 3 into place on Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter…
Space Shuttle Main Engine 3 install in Endeavor
This photo shows the second RS-25 engine attached to the core stage for NASA’s Space Launch System rocket for the agency’s Artemis I mission to the Moon. Engineers and technicians at NASA’s Michoud Assembly Facility in New Orleans structura…
Second RS-25 Engine Attached to NASA Moon Rocket
nside the world's largest clean room at NASA's Goddard Space Flight Center in Greenbelt, Md., engineers worked tirelessly to install another essential part of the James Webb Space Telescope - the Near Infrared Camera into the heart of the t…
Engineers Install Near Infrared Camera into the Heart of Webb Telescope
Employees maneuver a vertical engine installer into place on the A-1 Test Stand at Stennis Space Center on Sept. 23. Installation of the equipment was a milestone event as the historic stand underwent modifications for testing the powerpack…
A-1 Test Stand modifications
A Lockheed Martin Skunk Works technician takes a break for a photo. Note that the technician is wearing protective clean gear while sitting inside the X-59 engine inlet. Wearing this gear reduces the chance of any foreign objects from damag…
Engine Test Fit Install
The engine vertical installer for NASA’s Space Launch System (SLS) is inside the Vehicle Assembly at NASA’s Kennedy Space Center in Florida on April 25, 2019. The engine installer is being lifted up by crane for transfer to High Bay 3. The…
Engine Vertical Installer Arrival
The engine vertical installer for NASA’s Space Launch System (SLS) arrives at the Vehicle Assembly at NASA’s Kennedy Space Center in Florida on April 25, 2019. The engine installer arrived from the manufacturer, Precision Fabrication and Cl…
Engine Vertical Installer Arrival
The engine vertical installer for NASA’s Space Launch System (SLS) arrives inside the Vehicle Assembly at NASA’s Kennedy Space Center in Florida on April 25, 2019. The engine installer arrived from the manufacturer, Precision Fabrication an…
Engine Vertical Installer Arrival
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 1 on the space shuttle Endeavour.      The work is…
KSC-2012-3729
CAPE CANAVERAL, Fla. - In a view from the floor of Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engine RSME number 1 has been installed on space shuttle Endeavour. The orbiter is surround…
KSC-2012-3744
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 3 on the space shuttle Endeavour.      The work is…
KSC-2012-3781
CAPE CANAVERAL, Fla. – At NASA’s Kennedy Space Center in Florida, the Hyster forklift is used to deliver replica shuttle main engine RSME number 3 to Orbiter Processing Facility Bay 2 for installation on space shuttle Endeavour.      The wo…
KSC-2012-3769
CAPE CANAVERAL, Fla. - In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engines 3 RSME has been installed on the space shuttle Endeavour. The orbiter is surrounded by work platforms allowi…
KSC-2012-3784
CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 1 on the space shuttle Endeavour.       The work i…
KSC-2012-3726
CAPE CANAVERAL, Fla. – Technicians keep a close watch as the Hyster forklift backs away from the space shuttle Endeavour following installation of replica shuttle main engine RSME number 3 inside Orbiter Processing Facility Bay 2 at NASA’s…
KSC-2012-3783
CAPE CANAVERAL, Fla. - In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engine RSME number 1 has been installed on space shuttle Endeavour. The orbiter is surrounded by work platforms allo…
KSC-2012-3742
In Orbiter Processing Facility bay 2, technicians on a Hyster forklift install space shuttle main engine no. 3 into Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end…
Space Shuttle Main Engine 3 install in Endeavor
The engine vertical installer for NASA’s Space Launch System (SLS) arrives inside the Vehicle Assembly at NASA’s Kennedy Space Center in Florida on April 25, 2019. The engine installer arrived from the manufacturer, Precision Fabrication an…
Engine Vertical Installer Arrival
The engine vertical installer for NASA’s Space Launch System (SLS) is inside the Vehicle Assembly at NASA’s Kennedy Space Center in Florida on April 25, 2019. The engine installer is being lifted up by crane for transfer to High Bay 3. The…
Engine Vertical Installer Arrival