EXPLODING WIRE GUN WITH CAPACITORS
1301118
CAPE CANAVERAL, Fla. – On Launch Pad 39B at NASA's Kennedy Space Center in Florida, catenary wires are being suspended from the lighting masts on the lightning towers.  The catenary wire system under development for the Constellation Progra…
KSC-2009-2255
CAPE CANAVERAL, Fla. – On Launch Pad 39B at NASA's Kennedy Space Center in Florida, catenary wires are being suspended from the lighting masts on the lightning towers.  The catenary wire system under development for the Constellation Progra…
KSC-2009-2252
F-8 DFBW in flight
F-8 DFBW in flight
Lockheed Martin engineers at Michoud Assembly Facility in New Orleans, Louisiana, prepare elements of the Orion pressure vessel for welding on Sept. 23, 2015.  Part of Batch image transfer from Flickr.
Preparing Orion pieces for welding
Lockheed Martin engineers at Michoud Assembly Facility in New Orleans, Louisiana, prepare elements of the Orion pressure vessel for welding on Sept. 23, 2015. Part of Batch image transfer from Flickr.
Preparing Orion pieces for welding
A quality inspector checks NASA’s X-59 aircraft during the construction phase. The X-59 was built in Lockheed Martin’s Skunk Works facility in Palmdale, California.  Once the aircraft and ground testing are complete, the X-59 will undergo f…
Quality Inspection on X-59
Because the number two X-29 at NASA's Ames-Dryden Flight Research Facility (later the Dryden Flight Research Center) flew at higher angles of attack than the number one aircraft, it required a spin chute system for safety. The system deploy…
X-29 Number Two in Flight Closeup of Spin Chute Mechanism
A laser scans the inside of the X-59 aircraft’s lower engine bay at Lockheed Martin Skunk Works in Palmdale, California. These scans can help identify potential hardware or wiring interferences prior to the final installation of the engine…
Quesst Mission |Lower Engine Bay Laser Scan
OVERALL VIEW OF EXPLODING WIRE GUN
1301119
CAPE CANAVERAL, Fla. – On Launch Pad 39B at NASA's Kennedy Space Center in Florida, catenary wires are being suspended from the lighting masts on the lightning towers.  The catenary wire system under development for the Constellation Progra…
KSC-2009-2251
EXPLODING WIRE GUN, BLDG 4205, WITH BACKING BLOCK, BARREL, COPPER RIBBON WITH WIRE
1301117
STS078-397-010 (20 June - 7 July 1996) --- Payload specialist Jean-Jacques Favier, representing the French Space Agency (CNES), and astronaut Kevin R. Kregel, pilot, perform a successful Inflight Maintenance (IFM) on the Bubble Drop Particl…
BDPU IFM, Favier and Kregel repair a short in the experiment's wires
Lockheed Martin engineers at Michoud Assembly Facility in New Orleans, Louisiana, prepare elements of the Orion pressure vessel for welding on Sept. 23, 2015.  Part of Batch image transfer from Flickr.
Preparing Orion pieces for welding
F-8 Digital Fly-By-Wire aircraft in flight. The computer-controlled flight systems pioneered by the F-8 DFBW created a revolution in aircraft design. The F-117A, X-29, X-31, and many other aircraft have relied on computers to make them flya…
F-8 DFBW in flight
This photo shows the X-29 during a 1991 research flight. Smoke generators in the nose of the aircraft were used to help researchers see the behavior of the air flowing over the aircraft. The smoke here is demonstrating forebody vortex flow.…
X-29 at High Angle of Attack with Smoke Generators
Technicians preform some installation work in the mid-bay on the X-59 Quiet SuperSonic Technology or QueSST aircraft. The aircraft, under construction at Lockheed Martin Skunk Works in Palmdale, California, will fly to demonstrate the abili…
SEG 450 Mid Bay - Encoders
The X-59 team working on the aircraft’s wiring around the engine inlet prior to the engine being installed.  Once complete, the X-59 is designed to fly supersonic while reducing the loud sonic boom. The Quesst mission could help change the…
Quesst Mission | X-59 Engine Inlet
Installation of the 2D-S (2-Dimensional Stereo) optical array probe made by Stratton Park Engineering Company (SPEC)
Calibration Probes In the Tunnel
CAPE CANAVERAL, Fla. – On Launch Pad 39B at NASA's Kennedy Space Center in Florida, catenary wires are being suspended from the lighting masts on the lightning towers.  The catenary wire system under development for the Constellation Progra…
KSC-2009-2254
CAPE CANAVERAL, Fla. – On Launch Pad 39B at NASA's Kennedy Space Center in Florida, catenary wires are being suspended from the lighting masts on the lightning towers.  The catenary wire system under development for the Constellation Progra…
KSC-2009-2253
EXPLODING WIRE GUN, BARREL BLOCK ASSEMBLY, BLDG 4205
1301116
OSAM-1 Electrical Engineer Gregory Griffin tapes hardware on the underside of the OSAM-1 Servicing Payload inside cleanroom at Goddard Space Flight Center, Greenbelt Md., Aug 19, 2024. This photo has been reviewed by the Export Control Offi…
NASA Goddard Space Flight Center
Engineers from NASA Marshall Space Flight Center's Propulsion Department examine nozzles fabricated using a freeform-directed energy wire deposition process. From left are Paul Gradl, Will Brandsmeier, Ian Johnston and Sandy Greene, with th…
Engineers with nozzles fabricated using a freeform-directed ener
STS-44 Mission Specialist (MS) James S. Voss works under the middeck subfloor of Atlantis, Orbiter Vehicle (OV) 104, to repair humidity separator leakage problems. Voss is surrounded by several water tanks and a maze of shuttle wiring and p…
STS-44 MS Voss "Bilge Man" under OV-104's middeck subfloor repairs separator
Lockheed Martin engineers at Michoud Assembly Facility in New Orleans, Louisiana, prepare elements of the Orion pressure vessel for welding on Sept. 23, 2015.  Part of Batch image transfer from Flickr.
Preparing Orion pieces for welding
The Apollo hardware jammed into the F-8C. The computer is partially visible in the avionics bay at the top of the fuselage behind the cockpit. Note the display and keyboard unit in the gun bay. To carry the computers and other equipment, th…
F-8 DFBW on-board electronics
Artist concept of the X-59 three forths view top
X59_threeForths
This image shows the X-59’s engine inlet from the aft view, which is the rear of the airplane, looking forward. Once the aircraft and ground testing are complete, the X-59 will undergo flight testing, which will demonstrate the plane’s abil…
Quesst Mission | X-59 Engine Inlet
Panorama of the IRT engineering and ice cloud calibration team in the control room.  Shown on the left are the data and system engineers.  In the center with their backs to the camera are the wind tunnel operators who control the wind speed…
GRC-2023-C-02727
Research pilot Richard E. Gray, standing in front of the AD-1 Oblique Wing research aircraft.
EC82-17954
No more images