
CAPE CANAVERAL, Fla. – Inside Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians work inside the aft compartment of the space shuttle Endeavour as replica shuttle main engine RSME number 3 is installed…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians move the Hyster forklift into position for installation of replica shuttle main engine RSME number 3 on the space shuttle End…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 1 on the space shuttle Endeavour. The work is…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 1 on the space shuttle Endeavour. The work is…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians install replica shuttle main engine RSME number 3 on the space shuttle Endeavour. The work is part of Transition and Ret…

CAPE CANAVERAL, Fla. – A close-up view of replica shuttle main engine RSME number 1 recently installed on space shuttle Endeavour in Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida. The work is part of Trans…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 1 on the space shuttle Endeavour. The orbiter is s…

CAPE CANAVERAL, Fla. – Technicians keep a close watch as the Hyster forklift backs away from the space shuttle Endeavour following installation of replica shuttle main engine RSME number 3 inside Orbiter Processing Facility Bay 2 at NASA’s…

In Orbiter Processing Facility bay 2, technicians on a Hyster forklift maneuver space shuttle main engine no. 3 into place on Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, Kennedy Space Center Director Bob Cabana, center, uses a "T"-shaped tool to lock the space shuttle Endeavour's hatch as United Space Alli…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, Kennedy Space Center Director Bob Cabana, far right, watches as, left to right, United Space Alliance technicians Gary Hamilton, Bobby Wr…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, Kennedy Space Center Director Bob Cabana, far right, watches as, left to right, United Space Alliance quality inspector Ken Carson, along…

CAPE CANAVERAL, Fla. – While wearing a safety harness, United Space Alliance aerospace technician Greg Smith checks equipment during weight and center of gravity checks on the space shuttle Endeavour in Bay 2 of the Orbiter Processing Facil…

CAPE CANAVERAL, Fla. – Looking along the under belly toward the main landing gear of the space shuttle Endeavour, United Space Alliance technicians complete weight and center of gravity checks in Bay 2 of the Orbiter Processing Facility at…

CAPE CANAVERAL, Fla. – Looking along the under belly of the space shuttle Endeavour toward its main landing gear, United Space Alliance technicians complete weight and center of gravity checks in Bay 2 of the Orbiter Processing Facility at…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, a United Space Alliance technician monitors the nose landing gear during weight and center of gravity checks on the space shuttle Endeavo…

CAPE CANAVERAL, Fla. – Technicians keep a close watch as the Hyster forklift arrives at Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida. Replica shuttle main engine RSME number 3 is being delivered for installati…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians move the Hyster forklift into position for installation of replica shuttle main engine RSME number 3 on the space shuttle End…

CAPE CANAVERAL, Fla. - In this wide-angle view inside Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engines 3 RSME has been installed on the space shuttle Endeavour. The orbiter is surroun…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engine RSME number 1 has been installed on space shuttle Endeavour. The orbiter is surrounded by work platforms allo…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 1 at NASA’s Kennedy Space Center in Florida, technicians work with the Hyster forklift as replica shuttle main engine RSME number 3 is installed on the space shuttle Endeavour.…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 3 on the space shuttle Endeavour. The work is…

CAPE CANAVERAL, Fla. - In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engine RSME number 1 has been installed on space shuttle Endeavour. The orbiter is surrounded by work platforms allo…

CAPE CANAVERAL, Fla. – In an overhead view, technicians work inside the aft compartment of the space shuttle Endeavour during installation of replica shuttle main engine RSME number 3 in Orbiter Processing Facility Bay 2 at NASA’s Kennedy S…

CAPE CANAVERAL, Fla. – At NASA’s Kennedy Space Center in Florida, the Hyster forklift arrives at Orbiter Processing Facility Bay 2 delivering replica shuttle main engine RSME number 3 for installation on space shuttle Endeavour. The wo…

CAPE CANAVERAL, Fla. – At NASA’s Kennedy Space Center in Florida, the Hyster forklift arrives at Orbiter Processing Facility Bay 2 delivering replica shuttle main engine RSME number 3 for installation on space shuttle Endeavour. The wo…

In Orbiter Processing Facility bay 2, technicians on a Hyster forklift maneuver space shuttle main engine no. 3 into place on Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, Kennedy Space Center Director Bob Cabana holds the "T"-shaped tool he used to lock the space shuttle Endeavour's hatch. The orbiter is un…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, weight and center of gravity checks are being completed on the space shuttle Endeavour. The work is part of Transition and Retiremen…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, United Space Alliance aerospace Quality Assurance inspector Dave Bliss, left, and Spherion aerospace technician Scott Palmer complete wei…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, United Space Alliance technicians complete weight and center of gravity checks on the space shuttle Endeavour. The work is part of T…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, United Space Alliance technicians Gary Hamilton, left, and Joe Walsh close the space shuttle Endeavour's hatch. The orbiter is undergoing…

CAPE CANAVERAL, Fla. – Looking along the nose landing gear of the space shuttle Endeavour, United Space Alliance technicians complete weight and center of gravity checks in Bay 2 of the Orbiter Processing Facility at NASA’s Kennedy Space Ce…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, United Space Alliance technicians complete weight and center of gravity checks on the space shuttle Endeavour. The work is part of T…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, United Space Alliance technicians monitor an orbiter jack as weight and center of gravity checks are completed on the space shuttle Endea…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 1 on the space shuttle Endeavour. The work is…

CAPE CANAVERAL, Fla. - In a view from the floor of Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engine RSME number 1 has been installed on space shuttle Endeavour. The orbiter is surround…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 3 on the space shuttle Endeavour. The work is…

CAPE CANAVERAL, Fla. – At NASA’s Kennedy Space Center in Florida, the Hyster forklift is used to deliver replica shuttle main engine RSME number 3 to Orbiter Processing Facility Bay 2 for installation on space shuttle Endeavour. The wo…

CAPE CANAVERAL, Fla. - In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engines 3 RSME has been installed on the space shuttle Endeavour. The orbiter is surrounded by work platforms allowi…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, technicians use the Hyster forklift to install replica shuttle main engine RSME number 1 on the space shuttle Endeavour. The work i…

CAPE CANAVERAL, Fla. – Technicians keep a close watch as the Hyster forklift backs away from the space shuttle Endeavour following installation of replica shuttle main engine RSME number 3 inside Orbiter Processing Facility Bay 2 at NASA’s…

CAPE CANAVERAL, Fla. - In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, replica shuttle main engine RSME number 1 has been installed on space shuttle Endeavour. The orbiter is surrounded by work platforms allo…

In Orbiter Processing Facility bay 2, technicians on a Hyster forklift install space shuttle main engine no. 3 into Endeavour. Each space shuttle main engine is 14 feet long, weighs about 6,700 pounds, and is 7.5 feet in diameter at the end…

CAPE CANAVERAL, Fla. – While wearing a safety harness, United Space Alliance aerospace technician Greg Smith checks equipment during weight and center of gravity checks on the space shuttle Endeavour in Bay 2 of the Orbiter Processing Facil…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility OPF Bay 2 at NASA’s Kennedy Space Center in Florida, weight and center of gravity checks are underway on the space shuttle Endeavour. Monitoring data on the activity are United Space All…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, the space shuttle Endeavour's hatch has been locked and sealed in final preparation for its cross-country ferry flight to California.…

CAPE CANAVERAL, Fla. – In Orbiter Processing Facility Bay 2 at NASA’s Kennedy Space Center in Florida, Kennedy Space Center Director Bob Cabana, far right, watches as United Space Alliance technicians Gary Hamilton, foreground, and Joe Wals…